Skip to main content

Select preferred language from 'Translate' hidden side menu =>

Blog Navigation

By
                              Blog Navigation 
Post a Comment

Why some Analog Circuits Use Both Positive and Negative Voltages?

Image
By

 Purpose of Dual Power Supply in Analogue Circuit Design: Why Positive and Negative Voltages Matter

Look at the following two circuits…

A Push-Pull audio single-ended Amplifier: 

Audio Push-Pull Amplifier with single ended power supply

   Push-Pull Audio Amplifier with dual Power Supply:

Audio amplifier with duel power Supply

What is the difference between the two above circuits?

In the second circuit, there is an absence of an output coupling capacitor.

Why is a capacitor needed in the first circuit? It charges at a positive cycle and discharges at a negative cycle, generating an AC voltage across the speaker.

In the second circuit, at the positive input cycle, current flows to the speaker. At a negative input cycle, current is pulled from the negative supply through the speaker, thus eliminating the output capacitor.

The output coupling capacitor has a few disadvantages. It puts a limit on low-frequency response, it is bulky, and needs a high value for better low-frequency response; it may dry out, and needs a replacement after a certain period.

Conclusion: positive and negative supply is needed in a high-end, direct-coupled amplifier circuit that eliminates coupling capacitors.


Affiliate Link

🔹 FAQ Set:

Q1. Why do analogue circuits require both positive and negative voltages?

Analogue circuits often handle signals that swing above and below zero volts. Dual supplies (+V and –V) allow amplifiers to process AC signals symmetrically without distortion.

Q2. Can a circuit run on only one positive voltage?

Yes, but it limits signal range. Single-supply designs need biasing to shift the reference to mid-voltage, reducing dynamic range and accuracy.

Q3. What is the advantage of using dual power supplies in op-amp circuits?

Dual power supplies simplify biasing, enable true zero-volt output, and improve linearity for AC and DC signal amplification.

Q4. Can we use two negative voltages instead of one positive and one negative?

Not typically. Circuits depend on a common ground reference; using two negative rails without a positive reference can cause incorrect biasing.

Q5. Which applications mostly need dual-polarity power supplies?

Audio amplifiers, analogue signal processing, instrumentation amplifiers, and sensor interfaces often require ±12V or ±15V dual supplies.


More content like this: 

If you like my content, consider supporting us:

Gpay Support Link






Comments

Post a Comment

Popular Posts

Blog Navigation

By
                              Blog Navigation 
Post a Comment
Read more

What Happens to an Inductor’s Stored Energy When Current Stops?

By
Can the Energy Stored in an Inductor Be Used Practically? Applications, Benefits, and Real-World Examples. Why does an inductive load create sparking across contacts?  An inductor stores energy in the form of a magnetic field as long as current is flowing through it. As the current stops, the magnetic field began to collapse. Collapsing magnetic flux is also a rate of change of magnetic flux that will induce a large voltage spike (back EMF) across it. Energy stored in an Inductor:  Since this induced voltage is parallel to the inductor coil, it decays by converting it to heat across the coil resistance. In that process, the coil generates a magnetic field again due to the flow of decaying current through the coils, which results in electromagnetic interference in the radio operation and sparking across open contacts. Adverse effects of stored energy in an inductor:  Can we put this back-EMF into use? Yes. Practical Use of Stored Energy in an Inductor:  Spark-ignition...
Post a Comment
Read more

The Role of a Speaker Enclosure in Sound Quality (Explained)

By
Why Do Speakers Need Enclosures? Role in Sound Quality, Bass Enhancement, and Acoustic Performance Explained The sound emitted by the speaker at the front and back is exactly 180 degrees out of phase. If the enclosure is not used to isolate backwards radiated sound, it will cancel sound at the front by destructive interference. That will reduce speaker output greatly. Bass reflex port: Some ported enclosures use backwards radiated sound efficiently by phase shifting it by 180 degrees and radiating it from the front (or back), which adds up to the front sound by constructive interference. This increases speaker output, especially in the low-frequency range. More content related to this: Why are capacitors used in speakers? Why is speaker polarity important? Role of a magnet in a speaker FAQ Set: Q1: What is a speaker enclosure? A speaker enclosure is a box or housing that surrounds a speaker driver to control sound radiation and improve performance. Q2: Why are enclosures important for ...
Post a Comment
Read more

What is the definition of a DC bias voltage in electronics?

By
What is DC Bias Voltage used in Electronic circuits? — Definition, Importance & Practical Examples DC bias is simply a deliberate addition of a DC voltage to a (circuit) node to offset its operating voltage level. Voltage divider bias in a common emitter amplifier:  The most common and popular example of DC bias is the voltage divider bias in a common-emitter amplifier. What will happen if the DC bias is not given to the base of the above circuit? The transistor will act like a rectifier; it will amplify only the positive part of the signal, creating a distorted output that we don't want. Purpose: The purpose of the DC bias in the above circuit is to keep the base DC offset voltage sufficiently high to keep the base-to-emitter junction forward-biased all the time, considering the subtractive effect of the negative-going excursion of the AC input signal and power supply voltage variations. The typical value is 1.2V for the 12V VCC. Biasing is not always DC; it can be AC: AC bias...
Post a Comment
Read more

How Capacitors Smooth Voltage and Inductors Smooth Current?

By
How does a capacitor smoothens a voltage and how does an Inductor smoothen the current Take a large reservoir of water. Does the inlet of water increase the water level suddenly? No. Watertank analogy of a capacitor: Does the outlet of water suddenly decrease the water level? No. A capacitor is like a water tank. Inlet water is like a charging current. The outlet of water is like a discharge current. Water level is like the voltage of a capacitor. DC ripple filter: The process of how a capacitor maintains its voltage level is best explained by how a filter capacitor smoothens the DC ripple. When the incoming voltage increases, it charges to that voltage. When the incoming voltage decreases, it uses its stored energy to supply current to the load by maintaining the voltage level. As long as demand le less than supply, it comfortably maintains almost a constant level of voltage across the load. That is exactly what an overhead water tank in our home does when there is an irregular water ...
Post a Comment
Read more